Click to zoom
$520
Clear
Product short description:
  • 4 Analog DC Current Outputs
  • 4 Discrete Voltage I/O Channels
  • 12 to 32V DC Power (2.8W)
  • Modbus TCP/IP, Ethernet/IP, Profinet
  • i2o® peer-to-peer available for Modbus TCP/IP only

The XT1530 interfaces analog output and discrete I/O signals between measurement and control devices over Ethernet. Discrete I/O are individually configurable for input or high-side switched output operation.

RSS
TWITTER
Visit Us
Follow Me
LINKEDIN
Share

The XT1530 interfaces analog output and discrete I/O signals between measurement and control devices over Ethernet. Discrete I/O are individually configurable for input or high-side switched output operation.

Rugged construction, high density design, and easy USB-to-PC/Windows setup combine for a very effective I/O solution. These units are ideal for remote monitoring, distributed control, or SCADA applications.

Analog Output Ranges: 0-20mA DC, 4-20mA DC
Discrete Input/Output Ranges:
Input: 0-32V DC, TTL thresholds
Output: 0-32V DC, open-source, up to 250mA
Ethernet Communication:
Modbus TCP/IP, i2o® peer-to-peer available for Modbus TCP/IP only
Ethernet/IP
Profinet
10/100Base-T(X)
PriorityChannel™ device determinism
Power Requirement: 12 to 32V DC (2.8W)

Performance Specifications

IMPORTANT: To prevent damage or errors from grounded PCs and surges, Acromag strongly recommends use of the USB-ISOLATOR when configuring an XT1000 I/O module.

USB Interface

USB Connector:
Type: USB Mini-B type socket, 5-pin
Data Rate: 12Mbps. USB v1.1 and 2.0 compatible
Cable Length: 5.0 meters maximum
USB Transient Protection: Transient voltage suppression on power and data lines
Driver: Not required. Uses Windows (HID) drivers

Analog Output

Configuration: 4 output channels, each with a 16-bit D/A converter
Output Type: 0-20mA DC or 4-20mA DC, configurable by channel
Accuracy: Better than ±0.1% of span
Output Excitation: Separate inputs for 12V (10-15V) and 24V (20-28V) power sources. Diode-coupled to support redundancy.

Discrete Input

Input Type: 4 active-high, buffered inputs, with a common connection. Inputs are tied in tandem to output drains for optional loopback monitoring of output state.
Input Signal Voltage Range: 0 to 32V DC
Input Current: 280μA, typical at 32V DC
Input Signal Threshold: 1.7V DC typical with100mV of hysteresis
Input Resistance: 10K ohms, typical
Input Response Time: 10ms, nominal

Discrete Output

Output Type: 4 open-source, smart, p-channel mosfet switches with a common drain connection. Provides high-side (sourcing) switching between the load and return.
Output Signal Voltage Range: 0 to 32V DC. 6-32V excitation source required.
Output “ON” Resistance: 0.5 ohms typical, 1.0 ohms maximum
Output “ON” Current Range: 0 to 250mA DC, continuous (up to 1A total for all 4 channels combined)
Output Response Time: 10ms, nominal

Ethernet Communication

Protocols:
Modbus TCP/IP, i2o® peer-to-peer available for Modbus TCP/IP only
Ethernet/IP
or Profinet, depending on model number
Ethernet Communication Controller: Innovasic RapID™ Platform with PriorityChannel™ for determinism at the device regardless of network load.
Modbus TCP/IP (slave): Port 502 reserved. Supports up to 10 sockets.
i2o Peer-to-Peer (master/slave): Can map 4-channel input groups to output groups at two destination IP addresses. Timed or change-of-state updates. Supports GPRS/GSM systems.
Ethernet/IP (adapter): Supports 16 connections. EDS file on website
Profinet (server): Supports 1 connection. GSDML file on website
Connectors: Two shielded 8-pin RJ-45 sockets, 10BaseT/100BaseTX
Wiring: Auto-crossover for MDI or MDI-X
IP Address: User-configurable. 192.168.1.100 default static IP address
Data Rate: Auto-negotiated, 10Mbps or 100Mbps
Compliance: IEEE 802.3, 802.3u, 802.3x

Environmental

Operating Temperature: -40 to 60°C (-40 to 140°F)
Storage Temperature: -40 to 85°C (-40 to 185°F)
Relative Humidity: 5 to 95% non-condensing
Power Requirement: 12 to 32V DC (110mA maximum @ 24V)
Isolation: I/O channels (as a group), network (each port), and power circuits isolated from each other
Peak: 1500V AC, ANSI/ISA-82.01-1988
Continuous: 250V AC, 354V DC
MTBF: 445,034 hrs. at 25°C; 335,836 hrs. at 40°C
Shock Immunity: 25g, per IEC 60068-2-27
Vibration Immunity: 4g, per IEC 60068-2-64
Approvals: CE compliant. UL/cUL listings. ATEX Certified. Designed for Class I; Division 2; Groups ABCD; Zone 2. ATEX II 3 G Ex nA IIC T4 Gc -40°C < Ta < 80°C
Electromagnetic Compatibility (EMC) Compliance
Radiated Emissions: BS EN 61000-6-4, CISPR 16
RFI: BS EN 61000-6-2, IEC 61000-4-3
Conducted RFI: BS EN 61000-6-2, IEC 61000-4-6
ESD: BS EN 61000-6-2, IEC 61000-4-2
EFT: BS EN 61000-6-2, IEC 61000-4-4
Surge Immunity: BS EN 61000-6-2, IEC 61000-4-5

Physical

General: General purpose plastic enclosure for mounting on 35mm “T-type” DIN rail
Case Material: Self-extinguishing polyamide, UL94 V-0 rated, color light gray. General purpose NEMA Type 1 enclosure
Circuit Board: Military grade fire-retardant epoxy glass (IPC-4101/98)
I/O Connectors: Removable plug-in type terminal blocks rated for 12A/250V; AWG #26-12, stranded/solid copper wire
Dimensions:
Width = 22.5mm (0.9 inches)
Length = 114.5mm (4.51 inches)
Depth = 99.0mm (3.90 inches)
Shipping Weight: 0.5 pounds (0.22 Kg) packed

  • i2o® peer-to-peer available for Modbus TCP/IP only
  • i2o® peer-to-peer updates based on change-of-state and/or timed updates
  • Multi-function, multi-channel stand alone module is very economical
  • Built-in 10K ohm pull-down resistors for 2/3-wire sensors (contacts, promixity, TTL)
  • Configurable normal/reverse input logic
  • Outputs include built-in read-back capability
  • Easy setup with Windows software via USB
  • Continuously changing “heart-beat” register validates module operation
  • High-Density 22.5mm wide package with pluggable, front-facing terminals
  • Dual Ethernet 10/100 ports (auto-negotiation) reduce switch port requirements
  • 1500V AC isolation (between I/O, power, and network ports) and surge/transient protection
  • Supports bussed/rail and redundant power
  • -40°C to 70°C wide temperature operation
  • Withstands 25g shock and 4g vibration
  • • CE and UL/cUL Class 1 Div 2 Zone 2 approvals
  • • ATEX Certified.
How to Communicate with Acromag Modbus/TCP Modules from Ignition Software Application Note
Communicating with Ignition Software This document illustrates a procedure for configuring OPC tags intended for Acromag Busworks® Series Modbus/TCP modules using Windows software from Inductive Automation. It is assumed that the user has a working knowledge of OPC, Modbus TCP, and Ignition software. Product Features: BusWorks® Series 9xxEN Modules w/Modbus/TCP BusWorks® Series XT1xx1 Modules w/...
How to Save Money when Using i2o Over Cellular Networks Application Note
Minimizing Costs When Transmitting Data Over Cellular Networks Defining the Problem: Acromag has a peer-to-peer technology called i2o. It allows 2 or more modules to talk to each other and no network master or special software is required. I2o operates over any standard Ethernet media; Cat 5 or 6 copper, Fiber Optics, Radios or via Cellular....
How to Connect to Acromag Ethernet I/O Devices Application Note
Getting Connected to Acromag Ethernet I/O Devices These instructions summarize the basic steps you will have to take in order to initially connect an Acromag Ethernet I/O product to your Personal Computer (PC) or laptop. To connect an Ethernet device to your PC, consult with your network administrator and either temporarily change the TCP/IP configuration...
How to Communicate with Ethernet XT Profinet from Siemens S7-1200 PLC Application Note
EthernetXT Profinet and Siemens S7-1200 When setting up a Profinet network, Profinet controllers are programmed with a special Profinet Configuration tool, like the Step7 from Siemens. This document illustrates an example procedure for configuring communications between Acromag BusWorks® Series Profinet modules and a Siemens S7-1200 Programmable Controller. It is assumed that the user has a...
How to Communicate to Acromag Series Ethernet Modules from Red Lion HMIs Application Note
Red Lion HMIs This document illustrates a procedure for configuring message commands for Acromag Ethernet modules using the Red Lion Crimson 2.0 Software. It is assumed that the user has a working knowledge of the Crimson 2.0 software, as well as a Red Lion HMI. Setting up Communications From a new or existing project, double...

Manuals

XT1531 User Manual (Log in to download the file)

XT1532 User Manual (Log in to download the file)

XT1533 User Manual (Log in to download the file)

Ethernet XT Series Configuration Software (Log in to download the file)
Ethernet IP EDS For XTxxx2-000 Modules (Log in to download the file)
Profinet GSDML Files for XTxxx3-000 Modules (Log in to download the file)
ESW-MBLIB-DEMO (Log in to download the file)
AMTN-DEMO (Log in to download the file)
ATMX Demo Software (Log in to download the file)
  • Compare

    20RM-16-DIN: 19” rack-mount kit with DIN rail

    • 19" rack-mount kit with DIN rail
    $185
    Select options
  • Compare

    4001 Serial Cables

    5-foot ribbon cable, DB25 male and 26-pin female IDC connectors, for 3B/5B backpanel to Ethernet I/O module connection
    $95
    Select options
  • Compare

    5020-350: Toroidal AC Current Sensor

    • AC Current Sensor to precondition an AC current input signal
    • Highly accurate toroidal instrument transformer that converts an AC current signal to a safe, low level, DC milliampere signal (0 to 11.17mA).
    $50
    Select options
  • Compare

    5035 Series: Ethernet Cables

    • Ethernet straight cable, CAT5
    • Ethernet crossover cable, CAT5E
    • Low EMI Double-Shielded Ethernet Patch Cable
    $40$115
    Select options
  • Compare

    900EN: 5-Port Ethernet Switch

    • 10/100Mbps
    • 15 to 36V DC power supply required
    • Five shielded RJ-45 sockets, 8-pin, 10Base-T / 100Base-TX
    $340
    Select options
  • Compare

    AMTN, AMTX: ActiveX / .NET Controls for Modbus I/O

    • Modbus/TCP or Modbus/RTU
    • These ActiveX / .NET software controls provide a fast, easy way to communicate with any Modbus slave devices connected to your PC.
    • Get your Visual Basic, Visual C, .NET, Excel, or other compatible applications talking Modbus protocol within minutes.
    $260$350
    Select options
  • Compare

    BusWorks XT Connector Kit

    DIN rail bus power/excitation connector kit. Includes one DIN rail bus connector (1005-070), one left-side female connector terminal block (1005-220) and one right side male connector terminal block (1005-221).
    $30
    Select options
  • Compare

    DIN Rail: Type T

    • DIN Rail Strip, Type T
    $15$25
    Select options
  • Compare

    EIS-408: Industrial Ethernet Switch with 8 Web-Managed Ports & Redundancy

    • 6-Port Copper & 2-Port Fiber Web-Managed with Redundancy
    • 12 to 48V DC power supply required
    • Six copper 10Base-T / 100Base-TX, auto-MDI/MDIX and two fiber optic 100Base-FX, SC connectors
    $1,325
    Select options
  • Compare

    ESW-MBLIB: Ethernet Modbus C Library Software

    • Universal support for five operating systems
    • C source code provided
    • Demo program included
    $0$330
    Read more
  • Compare

    IMC-100A: 10/100BaseTX to 100BaseFX Industrial Media Converter

    • UTP to Fiber Media Converter
    • RJ45 Port Supports Auto MDI/MDI-X Function
    $240
    Select options
  • Compare

    PS5R: Slim Line Power Supplies

    • 10W, 15W, 30W, 60W, 90W, 120W, and 240W models
    • Universal Input (85-264V AC / 100-370V DC)
    • Lightweight and compact size
    $95$245
    Select options
  • Compare

    Terminal Block Replacements

    • Simplifies wiring connections on Acromag I/O Modules
    • Barrier strip or spring clamp terminal block kits
    • Provide safe and secure wiring connections
    $30$40
    Select options
  • Compare

    USB Isolator

    • USB-powered, USB 2.0 and 1.1 compatible
    • 1500V AC / 2100V DC isolation
    • No drivers required
    This compact, industrial-grade isolator provides a high-voltage isolation barrier between a computer and a connected USB device.
    $110
    Select options
  • Compare

    USB-to-Ethernet Adapter

    Simplifies configuration of Acromag Ethernet I/O Modules Prevents disruption of existing LANs This device is a USB-to-Ethernet adapter that you can use to communicate with any Acromag Ethernet I/O product for the purpose of setup and re-configuration for your application. It is recommended for initial communication with Acromag Ethernet devices so that you do not have to disrupt your existing network connection.
    $80
    Select options
  • Compare

    XT-SIP: Software Interface Package

    • Software Interface Package for BusWorks XT Series Ethernet I/O modules.
    • Includes configuration software CD-ROM (XT-CONFIG)
      • Isolator (USB-Isolator)
      • Ethernet cable (5035-360)
      • Two USB cables (4001-112, 4001-113)
    • Easy setup and digital calibration via USB with Windows configuration software
    • Download software only from the Software Tab below
    $185
    Select options

Additional information

Weight N/A
Dimensions N/A
Part Number

XT-SIP: Software Interface Package

  • Description

  • Features & Benefits

    • i2o® peer-to-peer available for Modbus TCP/IP only
    • i2o® peer-to-peer updates based on change-of-state and/or timed updates
    • Multi-function, multi-channel stand alone module is very economical
    • Built-in 10K ohm pull-down resistors for 2/3-wire sensors (contacts, promixity, TTL)
    • Configurable normal/reverse input logic
    • Outputs include built-in read-back capability
    • Easy setup with Windows software via USB
    • Continuously changing “heart-beat” register validates module operation
    • High-Density 22.5mm wide package with pluggable, front-facing terminals
    • Dual Ethernet 10/100 ports (auto-negotiation) reduce switch port requirements
    • 1500V AC isolation (between I/O, power, and network ports) and surge/transient protection
    • Supports bussed/rail and redundant power
    • -40°C to 70°C wide temperature operation
    • Withstands 25g shock and 4g vibration
    • • CE and UL/cUL Class 1 Div 2 Zone 2 approvals
    • • ATEX Certified.
  • Tech Papers

    How to Communicate with Acromag Modbus/TCP Modules from Ignition Software Application Note
    Communicating with Ignition Software This document illustrates a procedure for configuring OPC tags intended for Acromag Busworks® Series Modbus/TCP modules using Windows software from Inductive Automation. It is assumed that the user has a working knowledge of OPC, Modbus TCP, and Ignition software. Product Features: BusWorks® Series 9xxEN Modules w/Modbus/TCP BusWorks® Series XT1xx1 Modules w/...
    How to Save Money when Using i2o Over Cellular Networks Application Note
    Minimizing Costs When Transmitting Data Over Cellular Networks Defining the Problem: Acromag has a peer-to-peer technology called i2o. It allows 2 or more modules to talk to each other and no network master or special software is required. I2o operates over any standard Ethernet media; Cat 5 or 6 copper, Fiber Optics, Radios or via Cellular....
    How to Connect to Acromag Ethernet I/O Devices Application Note
    Getting Connected to Acromag Ethernet I/O Devices These instructions summarize the basic steps you will have to take in order to initially connect an Acromag Ethernet I/O product to your Personal Computer (PC) or laptop. To connect an Ethernet device to your PC, consult with your network administrator and either temporarily change the TCP/IP configuration...
    How to Communicate with Ethernet XT Profinet from Siemens S7-1200 PLC Application Note
    EthernetXT Profinet and Siemens S7-1200 When setting up a Profinet network, Profinet controllers are programmed with a special Profinet Configuration tool, like the Step7 from Siemens. This document illustrates an example procedure for configuring communications between Acromag BusWorks® Series Profinet modules and a Siemens S7-1200 Programmable Controller. It is assumed that the user has a...
    How to Communicate to Acromag Series Ethernet Modules from Red Lion HMIs Application Note
    Red Lion HMIs This document illustrates a procedure for configuring message commands for Acromag Ethernet modules using the Red Lion Crimson 2.0 Software. It is assumed that the user has a working knowledge of the Crimson 2.0 software, as well as a Red Lion HMI. Setting up Communications From a new or existing project, double...
  • Specs & Data Sheets

    Manuals

    XT1531 User Manual (Log in to download the file)

    XT1532 User Manual (Log in to download the file)

    XT1533 User Manual (Log in to download the file)

  • Software

    Ethernet XT Series Configuration Software (Log in to download the file)
    Ethernet IP EDS For XTxxx2-000 Modules (Log in to download the file)
    Profinet GSDML Files for XTxxx3-000 Modules (Log in to download the file)
    ESW-MBLIB-DEMO (Log in to download the file)
    AMTN-DEMO (Log in to download the file)
    ATMX Demo Software (Log in to download the file)
  • Accessories

    • Compare

      20RM-16-DIN: 19” rack-mount kit with DIN rail

      • 19" rack-mount kit with DIN rail
      $185
      Select options
    • Compare

      4001 Serial Cables

      5-foot ribbon cable, DB25 male and 26-pin female IDC connectors, for 3B/5B backpanel to Ethernet I/O module connection
      $95
      Select options
    • Compare

      5020-350: Toroidal AC Current Sensor

      • AC Current Sensor to precondition an AC current input signal
      • Highly accurate toroidal instrument transformer that converts an AC current signal to a safe, low level, DC milliampere signal (0 to 11.17mA).
      $50
      Select options
    • Compare

      5035 Series: Ethernet Cables

      • Ethernet straight cable, CAT5
      • Ethernet crossover cable, CAT5E
      • Low EMI Double-Shielded Ethernet Patch Cable
      $40$115
      Select options
    • Compare

      900EN: 5-Port Ethernet Switch

      • 10/100Mbps
      • 15 to 36V DC power supply required
      • Five shielded RJ-45 sockets, 8-pin, 10Base-T / 100Base-TX
      $340
      Select options
    • Compare

      AMTN, AMTX: ActiveX / .NET Controls for Modbus I/O

      • Modbus/TCP or Modbus/RTU
      • These ActiveX / .NET software controls provide a fast, easy way to communicate with any Modbus slave devices connected to your PC.
      • Get your Visual Basic, Visual C, .NET, Excel, or other compatible applications talking Modbus protocol within minutes.
      $260$350
      Select options
    • Compare

      BusWorks XT Connector Kit

      DIN rail bus power/excitation connector kit. Includes one DIN rail bus connector (1005-070), one left-side female connector terminal block (1005-220) and one right side male connector terminal block (1005-221).
      $30
      Select options
    • Compare

      DIN Rail: Type T

      • DIN Rail Strip, Type T
      $15$25
      Select options
    • Compare

      EIS-408: Industrial Ethernet Switch with 8 Web-Managed Ports & Redundancy

      • 6-Port Copper & 2-Port Fiber Web-Managed with Redundancy
      • 12 to 48V DC power supply required
      • Six copper 10Base-T / 100Base-TX, auto-MDI/MDIX and two fiber optic 100Base-FX, SC connectors
      $1,325
      Select options
    • Compare

      ESW-MBLIB: Ethernet Modbus C Library Software

      • Universal support for five operating systems
      • C source code provided
      • Demo program included
      $0$330
      Read more
    • Compare

      IMC-100A: 10/100BaseTX to 100BaseFX Industrial Media Converter

      • UTP to Fiber Media Converter
      • RJ45 Port Supports Auto MDI/MDI-X Function
      $240
      Select options
    • Compare

      PS5R: Slim Line Power Supplies

      • 10W, 15W, 30W, 60W, 90W, 120W, and 240W models
      • Universal Input (85-264V AC / 100-370V DC)
      • Lightweight and compact size
      $95$245
      Select options
    • Compare

      Terminal Block Replacements

      • Simplifies wiring connections on Acromag I/O Modules
      • Barrier strip or spring clamp terminal block kits
      • Provide safe and secure wiring connections
      $30$40
      Select options
    • Compare

      USB Isolator

      • USB-powered, USB 2.0 and 1.1 compatible
      • 1500V AC / 2100V DC isolation
      • No drivers required
      This compact, industrial-grade isolator provides a high-voltage isolation barrier between a computer and a connected USB device.
      $110
      Select options
    • Compare

      USB-to-Ethernet Adapter

      Simplifies configuration of Acromag Ethernet I/O Modules Prevents disruption of existing LANs This device is a USB-to-Ethernet adapter that you can use to communicate with any Acromag Ethernet I/O product for the purpose of setup and re-configuration for your application. It is recommended for initial communication with Acromag Ethernet devices so that you do not have to disrupt your existing network connection.
      $80
      Select options
    • Compare

      XT-SIP: Software Interface Package

      • Software Interface Package for BusWorks XT Series Ethernet I/O modules.
      • Includes configuration software CD-ROM (XT-CONFIG)
        • Isolator (USB-Isolator)
        • Ethernet cable (5035-360)
        • Two USB cables (4001-112, 4001-113)
      • Easy setup and digital calibration via USB with Windows configuration software
      • Download software only from the Software Tab below
      $185
      Select options
  • Additional information

    Additional information

    Weight N/A
    Dimensions N/A
    Part Number

    XT-SIP: Software Interface Package